How to Change Battery in Hyundai Key Fob

If you own a Hyundai, chances are you have a key fob. And if you have a key fob, chances are you’ll eventually need to change the battery. Here’s how to do it:

First, locate the release button on your key fob. It’s usually located on the back side of the fob. Once you’ve found the release button, press it and slide the back cover off of the fob.

Next, remove the old battery from the fob. You may need a small flathead screwdriver to help pry it out. Once the old battery is out, insert the new one making sure that the positive (+) side is facing up.

Replace the back cover of your key fob and press firmly until it snaps into place. That’s it! You’ve now successfully changed the battery in your Hyundai key fob.

Hyundai Kona & Palisade Key Fob Battery Replacement – DIY

  • Open the key fob by prying it open with a small screwdriver or other sharp object
  • Remove the old battery and insert the new one, making sure that the positive side is facing up
  • Close the key fob and test it to make sure that it is working properly

How to Replace Hyundai Key Fob

If your Hyundai key fob has stopped working, it may be time to replace the battery. But if that doesn’t fix the problem, you may need to replace the key fob itself. Here’s how to do it:

1. Start by removing the old key fob from your car’s keyring. Then, use a small screwdriver or other tool to pry open the back of the key fob. 2. Inside, you’ll see a small circuit board and battery.

Carefully remove both of these and discard them. 3. Now, take your new key fob and insert the battery (making sure it is oriented correctly). Then, snap the back of the key fob shut.

4. Finally, test out your new key fob by pressing the buttons to make sure they work properly. If all goes well, you’re all set!

How to Change Battery in Hyundai Key Fob

Credit: www.siddillon.com

What Kind of Battery Goes in a Hyundai Key Fob?

If you need to replace the battery in your Hyundai key fob, you will need a CR2032 3-volt coin cell battery. You can find these batteries at many stores, including drugstores, grocery stores, and electronics stores. Simply pop open the key fob and replace the old battery with the new one.

How Do You Change the Battery in a 2017 Hyundai Sonata Key Fob?

If you need to change the battery in your 2017 Hyundai Sonata key fob, here’s how to do it. First, remove the key fob from the key ring. Then, use a small flathead screwdriver or a paperclip to pry open the back of the key fob.

You should see a small battery inside. Use a Phillips head screwdriver to remove the two screws that hold the battery in place. Replace the old battery with a new CR2032 coin cell battery and reassemble the key fob.

How Do I Change the Battery in My Hyundai Iload Key?

If your Hyundai iload key has a dead battery, you’ll need to change it. Here’s how: 1. Start by removing the key from the ignition.

2. Locate the small hole on the back of the key. This is where the battery cover is located. 3. Use a small flathead screwdriver or other sharp object to pry open the battery cover.

Be careful not to damage the surrounding area. 4. Once the cover is off, remove the old batteries and insert new ones in their place (make sure they’re facing the correct way).

How Do You Change the Battery in a Hyundai Key Fob 2018?

If you have a Hyundai key fob from 2018 or later, changing the battery is a pretty simple process. Here’s what you’ll need to do: 1. Start by removing the key fob from your key ring.

There should be a small release button on the side that you can press to pop the fob open. 2. Once the fob is open, take out the old battery and note which way it was facing. You’ll want to insert the new battery in the same orientation.

3. Put in the new battery and then snap the fob back together. That’s it! Your new battery should now be working properly.

Conclusion

If your Hyundai key fob starts to act up, it might be time to change the battery. Here’s a quick and easy guide on how to do just that. First, locate the small screw on the back of the key fob.

Using a small screwdriver, remove this screw and then pry open the back of the key fob casing. Inside, you’ll see a small metal plate with a “+” sign on it. This is the positive end of the battery.

Gently pry this plate up and then remove the old battery from its slot. To insert the new battery, simply reverse these steps – insert the new battery into its slot (positive side facing up), replaced the metal plate, and then screw everything back together again.

Similar Posts