How to Put Spacebar Back on Keyboard

I don’t know about you, but I often find myself accidentally hitting the spacebar while I’m typing away on my laptop. And when I do, it’s always a pain to try and put the spacebar back on. Fortunately, there’s an easy way to do it.

  • Look for the tiny screws on the back of your keyboard
  • Unscrew those with a very small Phillips head screwdriver
  • Gently pry off the back cover of your keyboard
  • Find the wire harness that connects your spacebar key to your keyboard’s circuit board
  • If it is disconnected, reconnect it and then replace the back cover of your keyboard and screw it in place
  • If the wire harness is still attached, gently wiggle the spacebar key until it pops off of its mounting post on the circuit board
  • Once it is off, put a drop or two of super glue or epoxy onto the mounting post and then reattach your spacebar key, holding it in place until the glue dries (this will only take a few minutes)

How to Put Spacebar Back on Keyboard Macbook Air

If you have a MacBook Air, you may have noticed that the spacebar has come loose. This is a common problem with this model of computer, and it’s easy to fix. Here are the steps you’ll need to take to put your spacebar back on:

1. Start by powering off your MacBook Air. Once it’s shut down, flip it over so that the bottom is facing up. 2. Locate the two small screws near the hinge on the bottom of your laptop.

These screws hold the plate in place that covers the spacebar mechanism. 3. Use a Phillips head screwdriver to remove these two screws. Be careful not to lose them!

4. With the screws removed, you should be able to lift up the plate and see the mechanism underneath. 5. The spacebar itself is held in place by two small plastic clips. Gently pull on these clips until they release from their sockets and allow you to remove the spacebar itself.

6. Take a close look at how the spacebar is positioned in its socket before moving on – you’ll need to put it back in exactly the same way later on! If everything looks good, proceed to step 7…

How Do You Reattach a Spacebar?

A spacebar is one of the most important keys on a keyboard, and it’s also one of the easiest to break. If your spacebar has come detached, you might be wondering how to reattach it. The good news is that it’s actually quite easy to do.

All you need is a bit of glue and some patience. Here’s a step-by-step guide to reattaching your spacebar: 1) Start by cleaning both the key and the keyboard itself.

This will help the glue adhere better and prevent any dirt or debris from getting trapped under the key. 2) Next, apply a thin layer of glue to both the underside of the key and the spot on the keyboard where it goes. Be careful not to use too much glue – you don’t want it oozing out from under the key when you press it down.

3) Carefully align the key with its slot on the keyboard, then gently press down until it’s firmly in place. You might want to use something like a paperclip or toothpick to hold it in place while the glue dries. 4) Once the glue is dry, test out your newly attached spacebar by typing away!

How Do You Reattach a Spacebar on a Laptop Keyboard?

Assuming you are referring to a standard desktop keyboard, the process is as follows: 1. Turn the keyboard upside down and locate the small retaining clip that holds the spacebar in place. This clip is usually located near the center of the spacebar.

2. Use a small flathead screwdriver or other similar tool to carefully pry up on the retaining clip. Be careful not to damage the surrounding plastic. 3. Once the retaining clip has been pried up, remove it from its slot along with any attached springs or other hardware.

4. Align the spacebar over its proper location on the keyboard and press it down into place until it snaps into position. Make sure all springs or other hardware are properly in place before reattaching the retaining clip.

Why Can’T I Put Spacebar Back on Keyboard?

There are a few reasons why you might not be able to put the spacebar back on your keyboard. The first reason is that the plastic clips that hold the key in place may be broken. If this is the case, you will need to purchase a new key from your local computer store or online.

The second reason is that the metal spring underneath the key may be damaged or bent. This can usually be fixed by gently bending it back into place with a pair of needle nose pliers. If neither of these solutions work, then you may need to replace your entire keyboard.


If you’re like most people, you probably take your keyboard for granted. But what happens when something goes wrong? Like when your spacebar stops working.

If this happens to you, don’t panic. There are a few things you can try to get your spacebar back up and running. First, check to make sure that the spacebar is not physically stuck.

If it is, try gently prying it loose with a butter knife or a similar object. If that doesn’t work, try pressing down on the spacebar with more force than usual. If the physical issue is not the problem, then it’s likely a software issue.

To fix this, start by restarting your computer. This will reset any temporary glitches that may be causing the problem. If that doesn’t work, try updating your keyboard driver.

You can do this through Device Manager in Windows or by visiting the website of your keyboard’s manufacturer. Hopefully one of these solutions will help you get your spacebar back up and running again!

Similar Posts