If you have a Honda Civic, chances are that you will eventually need to change the battery in your key. This is a relatively easy process that anyone can do with a few simple tools. In this article, we will show you how to change Honda Civic key battery in just a few minutes.
Honda Key FOB Battery Change (Smart Key Remote) – For Accord, Civic, CRV, Pilot, Odyssey, Ridgeline
- Open the key fob by gently prying it open with a small screwdriver
- Remove the old battery and insert the new one, making sure that the positive (+) side is facing up
- Close the key fob and test it to make sure that it’s working properly
How to Change Honda Key Battery
Assuming you have a Honda with a keyless entry system, here are the steps to change the battery in your key fob. 1. Start by prying open the key fob casing with a small flathead screwdriver or knife. You should see a small gap between the two halves of the casing— insert your tool into this gap and gently twist until the two halves come apart.
2. Once you’ve opened up the key fob, locate the small circuit board inside and find the coin-shaped battery. 3. Use a Phillips head screwdriver to remove the screws holding down the battery cover, then carefully pry off the cover to expose the battery 4. Gently remove the old battery from its housing (be careful not to damage any of the surrounding electronics) and insert a new CR2032 3V lithium coin cell battery in its place
How Do I Change the Battery in My Honda Key?
If your remote key fob has a dead battery, you’ll need to replace it. Here’s a quick guide on how to do just that:
1. Start by locate the small release button on the back of the key fob.
This is usually located near the bottom. 2. Use a small object like a paperclip or pen tip to depress the release button and pull apart the two halves of the key fob. 3. Inside, you’ll find a small coin cell battery (CR2032).
Remove the old battery and replace it with a new one, making sure that the positive (+) side is facing up. 4. Reassemble the key fob and test it out by pressing any of the buttons. If it doesn’t work, make sure that the new battery is inserted correctly and try again.
What Battery Goes in a Honda Civic Key Fob?
There are a few different types of batteries that can be used in a Honda Civic key fob. The most common type is the CR2032 battery, which is a 3 volt coin cell battery. This type of battery can typically be found at most hardware or electronics stores.
Other types of batteries that can be used in a Honda Civic key fob include the CR2025 and the CR2016, which are both 3 volt coin cell batteries as well.
How Do You Change the Battery in a 2018 Honda Civic Key Fob?
If your 2018 Honda Civic key fob is not working properly, it may be time to change the battery. Here is a step-by-step guide on how to do so:
1. Start by locating the release button on the back of the key fob.
This is usually located near the bottom of the fob. 2. Use a small flathead screwdriver or a paperclip to press and hold down the release button. 3. While holding down the release button, use your other hand to twist and pull off the back cover of the key fob.
4. Once the back cover is removed, you should see a small metal key ring attached to a white plastic disc. The disc contains the battery for your key fob. 5. Use your fingernail or a small flathead screwdriver to gently pry up on one end of the battery until it pops out of its slot in the disc.
Be careful not to lose any of the small springs or clips that are underneath the battery as well!
How Do You Change the Battery in a 2016 Honda Civic Key Fob?
Assuming you have a key fob like this:
To change the battery in your 2016 Honda Civic key fob, follow these steps:
1. Using a small flathead screwdriver, pry open the cover of the key fob.
You should see the battery inside. 2. Remove the old battery and insert a new CR2032 coin cell battery in its place. Make sure the positive (+) side is facing up.
3. Snap the cover back on and you’re done!
If your Honda Civic key fob starts to act up, it might be time to change the battery. Here’s a quick and easy guide on how to do just that. First, you’ll need to find the right type of battery for your specific key fob.
Once you have the new battery, simply pop open the back of the key fob and replace the old battery with the new one. Make sure everything is snapped shut securely before trying to use your key again. With a fresh battery in your key fob, you should be good to go!